-
Air Drill Motor -
Low Friction Air Cylinder -
Motor Mount Set -
-
1/2" Needle Bearing -
Pipe Roller Top Bearing -
AKM Servo Motor with BiSS Encoder -
EC-22 Motor with Sensor for Drill -
V-Pulley Idle -
Arm -
Telescopic Unit Tube and Rod Set Includes:- Rod Set of 3 (Length=670 mm with machined edges) - Part #: M1-PN-0131
- Tube Set of 3 (Length=485 mm with machined edges) - Part #: M1-TU-0051
-
Stinger Assembly including Stinger Tips. -
PLC Communication Module -
Flow Tester Regenerative Turbine Pump -
Bowl Jam Sensor with Cable -
Arm Assembly -
Cool Tube Tip (select design type Original or New - review the gallery pictures) -
Stinger Tip -
Perforator Door Hinge with Switch -
Spring Anchor 6 mm -
Spring Anchor 5 mm -
Pipe Center Spring -
Set of all Springs on the DP Machine: -
Fiber Optic Fork Sensor -
Pipe Center Pulley Shaft -
Timing Belt Pulley T5-25 -
Timing Belt Pulley T5-48 -
Timing Belt Pulley T5-25 -
Timing Belt Pulley AT5-32 - Driving -
Belt Pulley AT5-25 - Idler (Legacy) -
Belt Pulley AT5-25 - Driving (Legacy) -
Timing Belt Pulley AT5-32 - Driving -
Belt Pulley AT5-25 - Driving (Legacy) -
Proportional Valve for Test-Pressure -
Proportional Valve for System-Pressure -
Indexer Servo Motor -
Cutting Device Clutch -
Servo Smart Drive (Kollmorgen) -
Inserting Drive Pulley -
Indexer Wheel with Short/Long Pins -
Encoder Mount Shaft -
Sensor Activator -
Rotating Moving Plate Shaft -
Pipe Center Bearing Guide Shutter -
Pipe Center Bearing Guid - Non-Detection Unit (Left Side) -
Pipe Center Bearing Guid - Detection Unit (Right Side) -
Drilling Dripper Guide Holds 6 mm (1/4") pipe during perforation -
Air Drill Motor Clamp for 6 mm (1/4") Pipe (Radius = 15.62 mm) -
Air Drill Motor Clamp for Two Drill Motors Center Distance 29 mm (Radius = 15.62 mm) Required Quantity per Set = 2 -
Air Drill Motor Clamp for Two Drill Motors Center Distance 23 mm (Radius = 15.62 mm) Required Quantity per Set = 2 -
Air Drill Motor Clamp for One Drill Motors (Radius = 15.62 mm) Required Quantity per Set = 2 -
Encoder 5,000 PPR (Pulse per Revolution)Â with Hollow Bore used with the RSP Perforator Model -
Encoder 10,000 PPR (Pulse per Revolution) with Hollow Bore used with the RSP Perforator Model
-
HMI Touchscreen with Program (FT) -
Conveyor Belt 38 mm x 5950 mm -
Ceramic Linear Bearing 1/4" ID, 1/2" OD -
Cam Follower -
B685ZZ Bearing for Inserting Belt Pulley T5-12 -
Inserting Belt Pulley T5-12 -
Pipe Center Swinging Arm SHORT - Assembly -
Pipe Center Swinging Arm LONG - Assembly -
Pipe Center Pulley Assembly -
Pipe Center Assembly - Non-Detection Unit -
Pipe Center Assembly - Detection Unit -
Stinger Tip Crimping Tool -
Disk V-Belt (Includes 43 Links) -
Bowl V-Belt (Includes 42 Links) -
Conveyor Motor and Gear -
Valve Assembly -
Upper Jaw Holders Set -
Inserting - Idler Pulley Assembly -
Cool Tube Assembly / Insertion tube Set (select design type Original or New - review the gallery pictures) -
-
Inserting Drive Pulley -
Indexer Home Sensor -
Inserter Servo Drive with Logic Controller -
Indexer Servo Drive with Logic Controller -
Fuse Package -
Out of stock
Indexer Funnel -
Cutting Knife 3" -
Toggle Block Bearing Spacer -
Dowel Pin Stop for Toggle Block -
CAM Support - Left -
CAM Support - Right -
-
Motor Mount -
Motor Mount -
Roller CAM Pointer -
Pipe Roller CAM -
Dowel Pin Pivot for Swing Arm -
Eccentric Plate -
Dowel Pin Pivot for Main Arm -
Dowel Pin Pivot for Main Latch Arm -
Swing Arm CAM Spacer -
Latch Stop - R -
Latch Stop - L -
Carriage Latch -
Pivot Block Bushing -
Driller Location CAM -
Swing Arm -
Swing Arm Stroke Reducer -
Leaf Spring - Long -
Leaf Spring - Short -
Stop Plate -
Main Arm -
Cam Jaw Axis 53 mm Length with Flats -
Carriage Drive Block -
Cam Wear Plate -
Cam Jaw Adjusters -
Carriage Impact Block -
Dowel Pin Pivot for Toggle Block -
Dowel Pin for Latch -
Toggle Block -
CAM Follower Mount -
Inserting Rod Head - Legacy -
Insertion Rod 8mm x 329mm -
Drive Block -
Roller Shaft Indexer -
Conveyor Pulley -
Indexer Wheel -
Inserting Rod Dead -
Pulley Shaft -
Power Filter -
Indexer Insert Choose Dripper diameter and enter Dripper Length [mm]- Note: The Insert total length will be about 7.5 mm shorter than the dripper length. Therefore the same Insert can accommodate similar length drippers.
-
Indexer Home Sensor -
Dripper Sensor -
Inserter Rod Home Sensor -
Conveyor Sensor -
Bowl Jam Sensor with Quick Disconnect -
Cutter Home Sensor -
Inserter Rod Home Sensor -
Bowl Sensor -
Part Present / Feeder Bowl Full Sensor -
Linear Slide Precision Shaft -
PLC with Program -
PLC Expansion Module -
Inserting Servo Motor -
-
Indexer Servo Motor -
Indexer Servo Motor Gearhead/Gearbox -
Cutting Device Servomotor -
Indexer Servo Drive -
Inserter Servo Drive -
-
Encoder for IN-xxx Machines -
Mechatrolink Cable 50M -
HMI Touchscreen with Program (IN-400) -
Rotor Clip for Inserting Idler Pulley -
Inserter PLC with Program -
Cutting Timing Belt
You must be logged in to view pricing. If you do not have an account, you can request a login.