- Rod Set of 3 (Length=670 mm with machined edges) - Part #: M1-PN-0131
- Tube Set of 3 (Length=485 mm with machined edges) - Part #: M1-TU-0051
-
Telescopic Unit Tube and Rod Set Includes: -
Stinger Assembly including Stinger Tips. -
PLC Communication Module -
Flow Tester Regenerative Turbine Pump -
Bowl Jam Sensor with Cable -
Arm Assembly -
Cool Tube Tip (select design type Original or New - review the gallery pictures) -
Stinger Tip -
Perforator Door Hinge with Switch -
Spring Anchor 6 mm -
Spring Anchor 5 mm -
Pipe Center Spring -
Set of all Springs on the DP Machine: -
Fiber Optic Fork Sensor -
Pipe Center Pulley Shaft -
Timing Belt Pulley T5-25 -
Timing Belt Pulley T5-48 -
Timing Belt Pulley T5-25 -
Timing Belt Pulley AT5-32 - Driving -
Belt Pulley AT5-25 - Idler (Legacy) -
Belt Pulley AT5-25 - Driving (Legacy) -
Timing Belt Pulley AT5-32 - Driving -
Belt Pulley AT5-25 - Driving (Legacy) -
Proportional Valve for Test-Pressure -
Proportional Valve for System-Pressure -
Indexer Servo Motor -
Cutting Device Clutch -
Servo Smart Drive (Kollmorgen) -
Inserting Drive Pulley -
Indexer Wheel with Short/Long Pins -
Encoder Mount Shaft -
Sensor Activator -
Rotating Moving Plate Shaft -
Pipe Center Bearing Guide Shutter -
Pipe Center Bearing Guid - Non-Detection Unit (Left Side) -
Pipe Center Bearing Guid - Detection Unit (Right Side) -
Drilling Dripper Guide Holds 6 mm (1/4") pipe during perforation -
Air Drill Motor Clamp for 6 mm (1/4") Pipe (Radius = 15.62 mm) -
Air Drill Motor Clamp for Two Drill Motors Center Distance 29 mm (Radius = 15.62 mm) Required Quantity per Set = 2 -
Air Drill Motor Clamp for Two Drill Motors Center Distance 23 mm (Radius = 15.62 mm) Required Quantity per Set = 2 -
Air Drill Motor Clamp for One Drill Motors (Radius = 15.62 mm) Required Quantity per Set = 2 -
Encoder 5,000 PPR (Pulse per Revolution) with Hollow Bore used with the RSP Perforator Model -
Encoder 10,000 PPR (Pulse per Revolution) with Hollow Bore used with the RSP Perforator Model
-
HMI Touchscreen with Program (FT) -
Conveyor Belt 38 mm x 5950 mm -
Ceramic Linear Bearing 1/4" ID, 1/2" OD -
Cam Follower -
B685ZZ Bearing for Inserting Belt Pulley T5-12 -
Inserting Belt Pulley T5-12 -
1/2" Needle Bearing -
Bowl V-Belt (Includes 42 Links) -
Conveyor Motor and Gear -
AKM Servo Motor with 2048 ppr Encoder -
Conveyor Belt 1" x 144" -
Indexer Servo Drive with Logic Controller -
Encoder Filter / Optical Isolator -
Cutter-HC with TiN Coating -
Servo Perforator Drive Belt -
CAM Jaw -
Pivot Block -
Wear Plate -
Drill Depth Adjuster Screw -
Main Arm Latch -
Arm -
Small Spring Anchor -
Large Spring Anchor -
Shock Absorber with Button -
Drill Knives Mini -
Drill Knife Regular -
Large Shock Absorber -
Large Air Piston / Cylinder -
Inserting Rod Aligner -
Large Cylinder Sensor -
Roller Lever Valve -
Nylon Thumb Screw -
Vibratory Feeder Control -
Snap Ring for Main Arm -
CAM Jaw Axis -
Pulley Shaft Cotter Pin -
Latch Shoulder Bolt -
-
Pulley Shaft Wave Washer -
Conveyor Belt 38 mm x 5950 mm
-
RBI Inserting Belt (Red Belt) -
AC Motor Speed Controller - 240 VAC -
AKM Servo Motor with BiSS Encoder -
Ultrasonic Sensor for Feeder Bowl -
Photoelectric Fork Sensor U-Shaped, 5 mm Slot -
Photoelectric Sensor for Dripper in Conveyor -
Bearing Type 625 -
Oil Free Bushing Holds Sensor Activator through the Perforator Right Plate -
X Axis Stage -
Timing Belt Pulley AT5-32 - Servo -
Timing Belt Pulley AT5-20 - Idler Unit -
HMI Touchscreen with Program (IN-250/300) -
Dripper Sensor Cable -
Dripper Sensor Amplifier -
PLC Battery (Yaskawa) -
Dripper Sensor Cable -
Large Shock Absorber -
Pipe Roller Bearing -
Inserter PLC with Program -
Rotor Clip for Inserting Idler Pulley -
Indexer Servo Drive -
Cutting Device Servomotor -
Indexer Servo Motor Gearhead/Gearbox -
Indexer Servo Motor -
-
Inserting Servo Motor -
PLC Expansion Module -
Low Friction Air Cylinder -
Linear Slide Precision Shaft -
Part Present / Feeder Bowl Full Sensor -
Bowl Sensor -
Inserter Rod Home Sensor -
Cutter Home Sensor -
Bowl Jam Sensor with Quick Disconnect -
Conveyor Sensor -
Inserter Rod Home Sensor -
Dripper Sensor -
Indexer Home Sensor -
Indexer Insert Choose Dripper diameter and enter Dripper Length [mm]- Note: The Insert total length will be about 7.5 mm shorter than the dripper length. Therefore the same Insert can accommodate similar length drippers.
-
Power Filter -
Pulley Shaft -
Inserting Rod Dead -
Indexer Wheel -
Conveyor Pulley -
Roller Shaft Indexer -
Drive Block -
Insertion Rod 8mm x 329mm -
Inserting Rod Head - Legacy -
CAM Follower Mount -
Toggle Block -
Dowel Pin for Latch -
Dowel Pin Pivot for Toggle Block -
-
Carriage Impact Block -
Cam Jaw Adjusters -
Cam Wear Plate -
Carriage Drive Block -
Cam Jaw Axis 53 mm Length with Flats -
Main Arm -
Stop Plate -
Leaf Spring - Short -
Leaf Spring - Long -
Swing Arm Stroke Reducer -
Swing Arm -
Driller Location CAM -
Pivot Block Bushing -
Carriage Latch